Digital Logic Lab Unit CPE-EO2100
Location :Home > Product Introduction > Edu. - ElectricityㆍElectronics > Digital Logic Lab Unit CPE-EO2100
Digital Logic Lab Unit
CPE-EO2100
CPE-EO2100
* Possible to make various digital IC circuit experiments and
practices.
* Very suitable to design various digital IC circuits.
* Suitable for TTL IC and C-MOS IC circuit experiments as this
equipment has a built-in +5V and -5V power.
* Hexadecimal FND display with 2 digit number.
* Very convenient to keep and carry as this equipment was
designed a suitcase-form.
practices.
* Very suitable to design various digital IC circuits.
* Suitable for TTL IC and C-MOS IC circuit experiments as this
equipment has a built-in +5V and -5V power.
* Hexadecimal FND display with 2 digit number.
* Very convenient to keep and carry as this equipment was
designed a suitcase-form.
Configuration/Specifications
1) DC output: +5V, -5V, 0.5A(Ripple 5mv Max.) Protection for over load
2) BCD display: 2 digits (Hexadecimal number indication)
1 2 3 4 5 6 7 8 9 A B C D E F
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
3) Indication polarity: Anode/Cathode Selectable Common Mode
4) Clock pulse output: 1Hz, 10Hz, 1kHz, 100kHz (High : 4.5V, Low:0.2V approx.)
5) Logic SW: 5 slide SW
6) 1 Push SW (Positive & Negative Edge Output)
7) Control SW: 1 Push SW Floating Contact
8) Protection: DC over load alarm & indication
9) Buzzer: Low power driver (3V~7V 1mA or less)
10) Variable resistance: 500kΩ (1ea), 10kΩ (1ea)
11) Volt meter: Full scale 20V (DC)
12) Ampere meter: Full scale 1A (DC)
13) Breadboard: Socket strip (630 hole) 3ea, Bus strip: 3ea
14) Input power: AC 220V, 50/60Hz
15) Dimension: 130(H) x 390(W) x 270(D)mm
16) Accessories
- Jumper wire: 1 set (red, yellow, green, white, black : 120ea)
- Instruction manual: 1 copy
2) BCD display: 2 digits (Hexadecimal number indication)
1 2 3 4 5 6 7 8 9 A B C D E F
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
3) Indication polarity: Anode/Cathode Selectable Common Mode
4) Clock pulse output: 1Hz, 10Hz, 1kHz, 100kHz (High : 4.5V, Low:0.2V approx.)
5) Logic SW: 5 slide SW
6) 1 Push SW (Positive & Negative Edge Output)
7) Control SW: 1 Push SW Floating Contact
8) Protection: DC over load alarm & indication
9) Buzzer: Low power driver (3V~7V 1mA or less)
10) Variable resistance: 500kΩ (1ea), 10kΩ (1ea)
11) Volt meter: Full scale 20V (DC)
12) Ampere meter: Full scale 1A (DC)
13) Breadboard: Socket strip (630 hole) 3ea, Bus strip: 3ea
14) Input power: AC 220V, 50/60Hz
15) Dimension: 130(H) x 390(W) x 270(D)mm
16) Accessories
- Jumper wire: 1 set (red, yellow, green, white, black : 120ea)
- Instruction manual: 1 copy
