Pulse Circuit Trainer CPE-EO2230
Location :Home > Product Introduction > Edu. - ElectricityㆍElectronics > Pulse Circuit Trainer CPE-EO2230
Pulse Circuit Trainer
CPE-EO2230
CPE-EO2230
* Easy to understand about circuit as each circuit is made up
on the panel.
* Possible to change every circuit constant.
* Possible to connect between circuits with an exclusive lead chip
as the input/output of every circuit is positioned on the exterior.
* Possible to make a practice without an external signal
generator.
on the panel.
* Possible to change every circuit constant.
* Possible to connect between circuits with an exclusive lead chip
as the input/output of every circuit is positioned on the exterior.
* Possible to make a practice without an external signal
generator.
Configuration/Specifications
1) Differentiator
- Input: amplitude -15V~15V, frequency 10kHz or less
- Internal condenser: 0.001㎌, 0.01㎌, 0.1㎌
- Internal resistance: 1kΩ, 10kΩ, 100kΩ
2) Integrator
- Input: amplitude -15V~15V, frequency 10kHz or less
- Internal condenser: 0.01㎌, 0.1㎌, 1㎌
- Internal resistance: 1kΩ, 10kΩ, 100kΩ
3) Clamper
- Input: amplitude less than -15V~15V
- Internal condenser: 100Hz~10kHz
- Internal power: about ±3V
- Internal resistance: 10kΩ, 100kΩ
4) Clipper
- Input: amplitude less than -15V~15V
- Internal condenser: 100Hz~10kHz
- Internal power: about ±3V
- Internal resistance: 10kΩ, 100kΩ
5) Gate/inverter amplifier AND, OR, NOT
- Input: Low level -0.7~0V, High level ≒12
- Output: Low level 0V~+0.7V, High level ≒12
- Frequency range: less than 10kHz
6) Miller/Boot-strap circuit
- Input range: less than ±15V
- Input frequency: less than 10kHz
7) Schmitt trigger circuit
- Input: amplitude more than 1Vp-p, frequency 50Hz~10kHz
- Output: ≒12V
8) Astable multi-vibrator
- Output amplitude: Low level : 0V~+0.7V High level : +10V~12V
- Internal condenser: C=0.01㎌, 0.1㎌
- Internal resistance: 56kΩ, 100kΩ
9) Monostable multi-vibration
- Input: amplitude more than 5Vp-p, frequency less than10kHz
- Internal condenser: C=0.01㎌, 0.1㎌
- Internal resistance: 56kΩ, 115kΩ
10) Bistable multivibrator
- Trigger input range: amplitude more than 5Vp-p, frequency less than10kHz
- J-K input: Low level 0V~+0.7V, High level ≒12
- Output amplitude: Low level 0V~+0.7V, High level ≒12
11) Signal source/DC power supply
- DC Power Suply
Output - DC ±12V, 0.5A
Protection - Turn off LED when over load
- Signal Generator
Output frequency - 100Hz/ 1kHz select output
Output Wave - Sine-wave, Square-wave
Output range - 0~10Vp-p
- On short output
Positive & negative pulse output
Input SW - ø12 push SW
- Logic SW
2H/L toggle switch
- LED indicator
2 positive Red LED
1 negative red LED
12) Experimental rack
- Setting up the module: 8ea
- Power supply bus(DC): 2 line & ground
13) Accessories
- Power cord: 1ea
- Module stored bag: 1ea
- Lead chip: 75ea
- User's manual: 1ea
- Input: amplitude -15V~15V, frequency 10kHz or less
- Internal condenser: 0.001㎌, 0.01㎌, 0.1㎌
- Internal resistance: 1kΩ, 10kΩ, 100kΩ
2) Integrator
- Input: amplitude -15V~15V, frequency 10kHz or less
- Internal condenser: 0.01㎌, 0.1㎌, 1㎌
- Internal resistance: 1kΩ, 10kΩ, 100kΩ
3) Clamper
- Input: amplitude less than -15V~15V
- Internal condenser: 100Hz~10kHz
- Internal power: about ±3V
- Internal resistance: 10kΩ, 100kΩ
4) Clipper
- Input: amplitude less than -15V~15V
- Internal condenser: 100Hz~10kHz
- Internal power: about ±3V
- Internal resistance: 10kΩ, 100kΩ
5) Gate/inverter amplifier AND, OR, NOT
- Input: Low level -0.7~0V, High level ≒12
- Output: Low level 0V~+0.7V, High level ≒12
- Frequency range: less than 10kHz
6) Miller/Boot-strap circuit
- Input range: less than ±15V
- Input frequency: less than 10kHz
7) Schmitt trigger circuit
- Input: amplitude more than 1Vp-p, frequency 50Hz~10kHz
- Output: ≒12V
8) Astable multi-vibrator
- Output amplitude: Low level : 0V~+0.7V High level : +10V~12V
- Internal condenser: C=0.01㎌, 0.1㎌
- Internal resistance: 56kΩ, 100kΩ
9) Monostable multi-vibration
- Input: amplitude more than 5Vp-p, frequency less than10kHz
- Internal condenser: C=0.01㎌, 0.1㎌
- Internal resistance: 56kΩ, 115kΩ
10) Bistable multivibrator
- Trigger input range: amplitude more than 5Vp-p, frequency less than10kHz
- J-K input: Low level 0V~+0.7V, High level ≒12
- Output amplitude: Low level 0V~+0.7V, High level ≒12
11) Signal source/DC power supply
- DC Power Suply
Output - DC ±12V, 0.5A
Protection - Turn off LED when over load
- Signal Generator
Output frequency - 100Hz/ 1kHz select output
Output Wave - Sine-wave, Square-wave
Output range - 0~10Vp-p
- On short output
Positive & negative pulse output
Input SW - ø12 push SW
- Logic SW
2H/L toggle switch
- LED indicator
2 positive Red LED
1 negative red LED
12) Experimental rack
- Setting up the module: 8ea
- Power supply bus(DC): 2 line & ground
13) Accessories
- Power cord: 1ea
- Module stored bag: 1ea
- Lead chip: 75ea
- User's manual: 1ea
